Download Commodity

Download Article

Vinyl fences are very resilient, so they don't crave a lot of maintenance. If some part does intermission, your fence is also easy to take apart and reassemble. The nigh difficult chore is finding an identical replacement piece. Once you have it, you tin apace connect it to the existing parts. Your repaired fence can then serve equally a feature of your home for many years.

Things Y'all Should Know

  • If a panel breaks on your vinyl fence, simply remove the pinnacle rail and panel from the department you want to replace, slide the new panels into place, and supersede the track.
  • You tin can also replace the rails by cutting it to length, removing the damaged rail, and sliding the new rails into the holes on the fence post.
  • If one of the posts gets damaged, unscrew the height rails, dig up the damaged post, gear up the new post in place with concrete, and reattach the runway and panels.

  1. 1

    Order like replacement panels. You can search online to find many different fence styles. If you lot can, contact the fence's manufacturer to get new panels identical to the old ones. Take a picture of your argue and transport information technology to companies to ensure you become the right panels.[1]

    • Endeavor to get replacement parts that are the same size and look equally close every bit possible to the residue of your contend.
    • Dwelling house comeback stores may as well sell argue parts and repair kits.

  2. 2

    Unscrew the top rail at the ends. The meridian rail attaches to the closest posts. Look for a pair of screws at the ends, securing the rail to those posts. Turn the screws counterclockwise to remove them, then set them aside.[ii]

    • These screws may be underneath the caps on the posts. Gently lift them with a hammer and chisel if you tin can't remove them by hand.
    • Keep the screws in a safe spot, such every bit a airtight container, so they can exist reused later.

    Advertisement

  3. three

    Remove the screws from the damaged panels. Now that the rail is free, locate the screws on the panels. If your fence'due south panels take pickets, or vertical bars, behind them, the screws may exist at the console's ends. Plow them counterclockwise to remove them.[3]

    • Not all fences accept pickets or screws. Your fence'south panels may be held in place with brackets, which you can slide the panels out of.

  4. iv

    Slide the panels out of the argue. Lift the peak rails off of the console you need to supplant. Then, pull the panel up to remove information technology. If yous took off all of the screws before, the console should come up off of the fence hands.[four]

    • If the console is next to a post, it may be attached with side brackets. Advisedly move the panel to the side and out of the brackets.

  5. 5

    Check the alignment of the posts with a level. Before installing the new panels, make sure the argue posts are level. Concur a level against the side of each connecting post. If a mail is positioned correctly, the level volition be appear flat from peak to bottom. Straighten the posts every bit needed.[5]

    • If your posts are held in the ground with concrete, they well-nigh likely will not need to exist adjusted.

  6. six

    Slide the new panels into the argue. Fit each panel over the bottom rail. Adjust the panels advisedly so each is level from top to bottom. Slide them into any nearby brackets, then place the acme rail over them. Brand sure each panel looks evenly spaced in the contend.[six]

    • In most fences, the panels volition fit right side by side to each other without leaving a gap.

  7. vii

    Screw the panels and top rail in place. Wait for the screw holes in the peak and lesser ends of each panel. Use these to fasten the panels to the stabilizing pickets, if your contend has them. Finish adjusting the top rail, then tighten the screws nigh the fence posts to secure it in place.[seven]

    • If the spiral holes do non line up, yous tin make full the existing console holes with spray foam, then drill new holes 1 in (ii.5 cm) deep.

    Advertizement

  1. 1

    Remove the panels from the track. If your fence's panels fasten to pickets, remove the screws at the top and bottom of the panels first. Then, slide the panels out of the rails. Clear the rails completely.[8]

  2. 2

    Unscrew the track from the posts. Each rail slides into holes on the posts. You will find a pair of screws holding the runway in position. Plough these counterclockwise and prepare them aside. Then, slide the rail off of the posts.[9]

    • Store the screws in a safe location and keep the sometime runway in instance you need to measure out them.

  3. 3

    Mensurate the length of rail you need. You tin can do this by running record measure from ane mail service to another. Recall that each rail needs to have a little extra length in order to slide into the post holes. Add about two in (v.1 cm) onto the length.[10]

    • If you have the erstwhile rails, you can also measure it for use equally an approximate.

  4. 4

    Wear prophylactic goggles and other protective gear. Before sawing into the rail, have the proper rubber precautions. Shield your eyes from debris past wearing safety goggles. Embrace your rima oris by wearing a respirator.

    • Avoid wearing loose clothing or jewelry when operating a saw.

  5. 5

    Cut the rail to length with a circular saw. Set the new rail on a workbench. Before cutting, mark where y'all need to make the cuts so you go the size of track yous demand. And then, advisedly cut through the rail.[eleven]

    • For the all-time results, cull a saw blade labeled for vinyl cutting. Fence companies and home comeback stores may sell these blades.

  6. 6

    Slide the rail into the holes on the fence posts. Make sure the brackets for the panels are on the superlative side. Push the track into the mail service holes until the runway hangs in place. As long as the rails is the right length, it should fit.[12]

    • If the runway doesn't fit properly, check the length once more. You may need to cutting it a little shorter.

  7. 7

    Spiral the rails to the posts. Locate the screw holes on either end of the rail. You will demand a pair of screws on each side. Twist them clockwise to lock the runway in place. When you're done, you can begin installing the vinyl panels.[xiii]

    • The size of screws you lot need differ from runway to rail.
    • Screws are commonly included with new rails, but yous tin try using the screws from the old rail.

    Advertisement

  1. one

    Unscrew the connecting rails. Each rail slides into slots on the post and is held in place with screws. Plow the screws counterclockwise to remove them. Pull both the top and lesser rails abroad from the postal service.[xiv]

    • If you have trouble installing a post, removing the rails and fence panels completely can requite you more infinite.

  2. 2

    Dig out the damaged post. Remove the old mail service as well equally any fragments that may be in the ground. If your mail was held in place with concrete, yous will need to dig up the concrete to remove it.[fifteen]

    • To remove the concrete, dig out the clay around information technology. You can refill the hole later.

  3. 3

    Measure where the new post will be placed. To figure out where to place the new postal service, measure the distance between ii existing posts. The new post should be placed an equal distance from the concluding post. Marker the location with paint, tape, or another indicator.[16]

    • The post needs to exist even and straight or else the track and panels will non fit correctly.

  4. 4

    Dig a hole three ft (0.91 chiliad) deep in the basis. Dig out the spot you marked earlier. Make the pigsty about 8 in (20 cm) in bore. You lot can apply a tape measure out to ensure the hole is the size you need.

  5. 5

    Seal the pole in identify with concrete. You volition need nigh 120 lb (54 kg) of premixed physical for i post. Place the post in the hole. While someone holds the post in position, fill up the the pigsty with concrete. Cascade the physical until it is about 4 in (10 cm) beneath the ground'southward surface.[17]

    • The other person should hold the mail direct. If it doesn't await right, conform information technology quickly earlier the concrete solidifies.

  6. 6

    Reinstall the debate rails and panels. Fit the fence rails into the holes on the new post, then begin sliding the panels onto the rails. Screw the track to the inside of the post. And then, attach the panels, screwing them in place if they also employ screws.[xviii]

    Advert

Add New Question

  • Question

    How can I repair a break in one of the panels on my fence?

    Ryaan Tuttle

    Ryaan Tuttle is a Home Improvement Specialist and the CEO of Best Handyman Boston. With over 15 years of experience, Ryaan specializes in abode improvement and property maintenance by leveraging technology and craftsmanship. Ryaan holds his Construction Supervisor and Dwelling Comeback Contractor Licenses. Unlike most handyman contractors, Best Handyman Boston is licensed and insured. Boston Mag and LocalBest.com accept named Best Handyman Boston the Best Handyman in Boston.

    Ryaan Tuttle

    Dwelling Improvement Specialist

    Practiced Respond

    You really would want to try to remove whatever panel that is. Any repair that you would make to it would be temporary, and it would but break once again over time. You could try gluing information technology, but really it should be replaced if possible.

Inquire a Question

200 characters left

Include your e-mail address to get a bulletin when this question is answered.

Submit

Advertisement

  • Keep any extra panels y'all take after installing your contend.

  • At that place are many different vinyl fence styles, then finding the right parts can take some time and patience.

  • Take a picture of your fence so y'all tin get the correct replacement parts.

  • To keep your vinyl contend in good shape, you'll likely need to clean information technology approximately once or twice a year in addition to making any needed repairs.

Ad

Things You'll Need

  • Replacement panels
  • Screwdriver
  • Replacement rail
  • Screwdriver
  • Measuring record
  • Prophylactic goggles
  • Respirator
  • Circular saw
  • Replacement post
  • Screwdriver
  • Shovel
  • Cement
  • H2o
  • Mixing container
  • Measuring tape

References

About This Article

Cheers to all authors for creating a folio that has been read nineteen,566 times.

Reader Success Stories

  • Sergiu Gojan

    Sergiu Gojan

    Nov x, 2021

    "Thanks for your difficult work, for drawing all these pictures and writing, you practise a great chore!"

Did this article help y'all?